Skip to main content
Our inboxes and phones are busier than ever after the CO-DRIVER NO3 launch. Every message is read by a real person on our team - we’ll get back to you as soon as we can. Thank you for your patience! ☺️

Where and how should I mount my CO-DRIVER?

  • Updated
OOONO – Where and how should I mount my CO-DRIVER?
OOONO CO-DRIVER

Find the perfect spot

Once your CO-DRIVER is set up, it's time to find the right spot for it in your car. Mounting works a bit differently depending on which CO-DRIVER you have.

Click your model below to jump straight to your guide.

CO-DRIVER NO3 CO-DRIVER NO3 CO-DRIVER NO2 CO-DRIVER NO2 CO-DRIVER NO2 PLUS CO-DRIVER NO2 PLUS CO-DRIVER NO1 CO-DRIVER NO1
CO-DRIVER NO3

Mounting your CO-DRIVER NO3

CO-DRIVER NO3 mounted on a car dashboard

How does the CO-DRIVER NO3 attach?

Your CO-DRIVER NO3 comes with two magnetic mounting pads already fixed to the back, each covered by a red protective film. Once the pads are stuck to a surface in your car, the device clicks onto them magnetically — so it stays put while you drive, and you can lift it off whenever you need to, for example to charge it.

Upgrading from a CO-DRIVER NO2? The CO-DRIVER NO3 uses the same magnet pads as the CO-DRIVER NO2. If the pads from your CO-DRIVER NO2 are already stuck in your car, you can simply click your CO-DRIVER NO3 onto them - no need to stick on new ones.

Choosing the right spot

The display is also the button you press to confirm, dismiss and report warnings, so pick a spot that's within easy reach and where you can glance at the screen without it blocking your view of the road.

Before you stick the padsNot every surface is a good match

The pads use a strong 3M adhesive. On some materials it may not hold as well, or it could leave marks or damage the surface if you remove the pads later. That's why we don't recommend sticking them on:

  • leather or faux leather
  • soft-touch or rubber-coated surfaces
  • fabric, Alcantara or suede
  • wood veneer or other delicate trim
  • surfaces recently treated with cockpit spray or other care products
  • airbag covers

Our tip: a smooth, hard, flat plastic surface gives the best result. If you'd still like to use one of the surfaces above, that's entirely your choice - just keep in mind that it's at your own risk.

How do I mount it?

  1. 1

    Clean the spot. Wipe it so it's clean, grease-free and fully dry. The adhesive bonds best when the surface isn't cold - around 15°C is ideal.

  2. 2

    Find the right spot. Choose a flat surface - the back of the CO-DRIVER NO3 is flat, so the pads need a flat area to stick properly. Hold the CO-DRIVER in a few places until you find the best one. Keep the red film on until you're sure - once the adhesive touches the surface, the pads can't be repositioned.

  3. 3

    Stick the pads on. Peel off the red film, place the CO-DRIVER with the pads attached against the surface and press for about 10 seconds.

  4. 4

    Lift the CO-DRIVER off. Carefully take the CO-DRIVER off the pads - the pads stay on the surface.

  5. 5

    Press the pads. Press firmly on the pads themselves, without the CO-DRIVER, for 20-30 seconds.

  6. 6

    Let it dry, then click it on. Let the adhesive dry without the CO-DRIVER attached - for at least a couple of hours, ideally 24 hours. That way the adhesive reaches its full strength. Then simply click your CO-DRIVER onto the pads - after that, you can take it off and put it back as often as you like.

Need to remove the magnet pads? Slide a thin, stiff, blunt tool carefully between the surface and the pad, and work it in gently until the pad lifts enough to grip with your fingers.

Once the adhesive magnet pads have been removed, they can't be used again — you'll need a new set, which you can get in our shop.
CO-DRIVER NO2 & NO2 PLUS

Mounting your CO-DRIVER NO2

What are the two magnets on the device for?

The built-in magnets allow you to mount your CO-DRIVER easily and flexibly in your car — exactly where it works best for you. They keep the device securely in place while driving.

Where can I find the magnets?

The two adhesive magnets are already attached to the back of your CO-DRIVER. You'll recognise them by the red protective film.

Only remove the red protective film once you have found a spot for your CO-DRIVER. Once attached, the metal parts cannot be moved anymore. If you wish to remove the magnets, we recommend using a thin, stiff, blunt tool to carefully wedge between the mounting surface and the magnetic base until the magnet lifts enough to grasp with your fingers.

CO-DRIVER NO2 magnet placementCO-DRIVER NO2 mounted in car

How do I mount using the magnets?

Pick a spot that's within easy reach, so you can press your CO-DRIVER quickly when a warning comes up.

Not every surface is a good match The magnet pads on the CO-DRIVER NO2 are the same as on the CO-DRIVER NO3, so the same surface advice applies: a smooth, hard, flat plastic surface gives the best result. See which surfaces we don't recommend.
  1. 1

    Clean the spot. Wipe it so it's clean, grease-free and fully dry. The adhesive bonds best when the surface isn't cold - around 15°C is ideal.

  2. 2

    Find the right spot. Hold the CO-DRIVER in a few places until you find the best one. Keep the red film on until you're sure - once the adhesive touches the surface, the magnets can't be repositioned.

  3. 3

    Stick the magnets on. Peel off the red film, place the CO-DRIVER with the magnets attached against the surface and press for about 10 seconds.

  4. 4

    Lift the CO-DRIVER off. Carefully take the CO-DRIVER off the magnets - the magnets stay on the surface.

  5. 5

    Press the magnets. Press firmly on the magnets themselves, without the CO-DRIVER, for 20-30 seconds.

  6. 6

    Let it dry, then click it on. Let the adhesive dry without the CO-DRIVER attached - for at least a couple of hours, ideally 24 hours. That way the adhesive reaches its full strength. Then simply click your CO-DRIVER onto the magnets - after that, you can take it off and put it back as often as you like.

How do I mount using the MOUNT?

The MOUNT offers a practical and secure way to mount your CO-DRIVER in your car, keeping it easily accessible at all times. Get the MOUNT in our shop.

Your package includes two magnetic metal plates. For the CO-DRIVER NO2, use the smaller metal plate.

  1. 1

    Stick the CO-DRIVER directly onto the smaller magnetic plate using the adhesive pads.

  2. 2

    Press the metal plate firmly against the CO-DRIVER for about 20 seconds.

  3. 3

    The metal plate is now firmly attached. Simply clip the MOUNT to the air vents in your car — the CO-DRIVER will stay securely in place while driving.

How do I mount my CO-DRIVER NO2 PLUS using the MOUNT NO2?

Your CO-DRIVER NO2 PLUS comes with the MOUNT NO2, which lets you attach the device to your car's sun visor.

  1. 1

    Remove the protective film from the adhesive strips on the magnets.

  2. 2

    Make sure the magnets are attached to the back of the CO-DRIVER and press it onto the MOUNT NO2.

  3. 3

    Clip the MOUNT NO2 (with the device attached) to your sun visor.

Thanks to the adhesive magnets, you can easily detach the device to charge it — and click it back into place when you're ready to go.

For more information: How do I use the OOONO Mount?

MOUNT NO2 on sun visorCO-DRIVER NO2 PLUS with MOUNT NO2
CO-DRIVER NO1

Mounting your CO-DRIVER NO1

CO-DRIVER NO1 mounted in carCO-DRIVER NO1 adhesive mount

How do I mount using the adhesive pads?

The device has adhesive strips on the back which can be used to attach the CO-DRIVER wherever it is convenient for you in the car. Unlike the CO-DRIVER NO2 and NO3, the strips hold the CO-DRIVER NO1 itself - so it stays where you stick it.

  1. 1

    Clean the spot. Wipe it so it's clean, grease-free and fully dry. The adhesive bonds best when the surface isn't cold - around 15°C is ideal.

  2. 2

    Find the right spot. Hold the CO-DRIVER in a few places until you find one that's within easy reach. Keep the red film on until you're sure - once the adhesive touches the surface, the CO-DRIVER can't be repositioned.

  3. 3

    Stick it on. Peel off the red film and press the CO-DRIVER firmly onto the surface.

How do I mount using the MOUNT?

The MOUNT is an extra accessory you can purchase on our website. It lets you securely mount your CO-DRIVER and keep it easily accessible at all times. Get the MOUNT in our shop.

Your MOUNT package includes two magnetic metal plates. For the CO-DRIVER NO1, use the bigger metal plate.

  1. 1

    Remove the red protective film from the adhesive strips on the back of your CO-DRIVER.

  2. 2

    Press the metal plate firmly against the adhesive strips for about 20 seconds.

  3. 3

    The metal plate is now firmly attached. Simply clip the MOUNT to the air vents in your car.

For more information: How do I use the OOONO Mount?

More resources

Related articles

You might also find helpful
Where and how should I mount my P-DISC?P-DISC
How do I turn the CO-DRIVER off and on?Functionality
How do I use the OOONO Mount?MOUNT